Plumbing 101: A Guide to Bathtub Installation
Plumbing 101: A Guide to Bathtub Installation
Blog Article
This great article following next in relation to How to Install a Bathtub is relatively remarkable. Don't overlook it.
Mounting a bath tub isn't specifically brain surgery, yet it does require strong plumbing, carpentry, and in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately hard project. If the old tub is easily accessible, the job can relocate rapidly; if you have to open up a wall to eliminate the old bathtub and position the brand-new tub, the job is much harder. In either situation, the task is within a residence handyman's abilities, although you will certainly need a helper to vacate the old bathtub and embeded in the brand-new one. See to it you have certified on your own for the job and are comfortable attempting it. As opposed to working with a professional to take over a halfway-completed job, it is much better to consider employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This post will help you install a brand-new tub in your shower room if you have already bought a brand-new bathtub and also don't require to alter the plan of your previous water pipelines.
Your tools and also material checklist should comprise the following:
Planning for the Setup
To start with, the supporting framework provided with the bath should be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to avoid stress on the bath tub.
Fit the versatile faucet adapters to the bottom of the two taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be suited its final position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, turn on the faucets to drain any water staying in the system. The procedure of getting rid of the existing taps can be rather problematic due to the restricted accessibility that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipes. When the supply pipelines have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this process. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Prior to going on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Utilizing both wood boards under its feet, place the tub in the required setting. The wood boards are helpful in evenly spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bathtub up until the level reviews level.
To install faucets, fit the bottom of the furthest flexible faucet adapter to the appropriate supply pipeline by making a compression join; then do the same for the other tap.
Activate the water supply and also check all joints and also new pipework for leaks and also tighten them if needed. Load the bathtub as well as likewise inspect the overflow electrical outlet and the regular outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the tub needs to wait till the bath tub has actually been made use of at least once as this will resolve it right into its final position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the manufacturer given backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap connectors. The former kind should be linked to the tap finishes initially, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to split a stiff seal, triggering the water to pass through the wall surface between the bath and the tiling, causing difficulties with dampness and possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, as well as can securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly load the tub with water prior to sealing, to allow for the activity experienced when the bathtub is in use. The sealant can crack rather very early if you do not take into consideration this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently readily available on the market. It is a good idea to fit the floor tiles utilizing water-resistant or water-proof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about Tools You Need to Install a New Bathtub ? Post a remark down below. We will be glad to know your responses about this write-up. In hopes to see you back again later on. Sharing is caring. You never know, you may just be helping someone out. Thanks for your time spent reading it.
Act now! Report this page